Over 20 years of experience. Every file our own, every result on the dyno.

Microchips Tuning is an ECU calibration workshop in Moschato, Athens. We don't sell off-the-shelf files or promises: every car is measured before, calibrated live on our own dyno and measured again after. You leave with the chart in your hand.

01Our story

The hard way, from day one.

Microchips Tuning started in 2003, when "tuning" in Greece usually meant a file from the internet and a lot of luck. We chose the hard way from the start: with an engineering approach, learn every ECU from the inside and write our own files, here in Athens.

More than twenty years later, the way we work hasn't changed. The cars, the tools and the ECUs have — from early diesels to today's tuning-protected Tricore units. Over 1000 cars have been documented on our dyno.

Many customers come from Zakynthos, Patras, Ioannina and Grevena — 400 and 650 km away — and come back with their next car.

The first Microchips Tuning shop
Our first shop: an office and a small workshop for the programming. Back then, every measurement was done on a rented dyno.
Our premises in Moschato, with the Dyno on the ground floor.
Our premises in Moschato, with the Dyno on the ground floor.
2003in tuning since
1000+cars on our dyno
800 psper axle · 4WD Dimsport
600+Facebook recommendations
02How we work

Five principles that don't change.

MCT / 011/5

We measure, we don't promise.

Figures don't come from a catalogue. They come from our 4WD Dimsport dyno, repeatable to 1–2 ps, so the difference you see is real.

MCT / 022/5

Every file, for your car.

Calibration is done live, with the ECU connected and the car under load. Point by point, within safe limits for engine, gearbox and clutch.

MCT / 033/5

We check first, then improve.

An engine with a boost leak, a tired turbo or a DPF problem needs fixing first. The dyno often reveals faults missed elsewhere — and we tell you before touching anything.

MCT / 044/5

You're there.

You see the runs, ask anything, and we explain what we changed and why. No secrets, no "magic".

MCT / 055/5

We also say no.

If a tune makes no sense for your car or can't be done properly, we'll tell you. We'd rather lose a job than a customer.

03The workshop

"More like an operating theatre than a garage."

That's how one customer described it. A clean, organised workshop in Moschato, built around the dyno.

  • 4WD Dimsport dyno, up to 800 ps per axle
  • Brakes for calibration under steady load
  • High-flow cooling for realistic temperatures
  • Equipment: Autotuner, Flex, CMD, Kess, Ktag, X17, Byteshooter, MPPS, Bitbox, PCMflash
  • OBD, bench, BDM and Tricore
Dyno →
Dimsport 4WD dyno
04How we work

Personal work, from start to finish.

We're not a chain and we don't push ready-made files through a queue. Every calibration is written here, with engineering know-how, and tested on our own dyno.

You talk directly to the person who will work on your car, from the first phone call to the last dyno run. At the end you know exactly what we changed and why, with the graph in your hand.

“One of the few cases, especially in the car world, where you leave feeling you got more than you paid for.”— Perikles V., on Facebook
Porsche Macan on the Microchips Tuning dyno
05Beyond the workshop

Partners all over the planet.

Beyond the cars we measure on our own dyno, workshops and tuners all over the planet work with files written by us. Every file comes with a WTC (What To Check) sheet listing what to check on the test drive.

Most of our partners are in Greece, and we work with professionals in countries such as Italy, Sweden, Portugal, Brazil, the USA, the United Arab Emirates and South Africa, with daily support from us.

Are you a workshop or a tuner? Get in touch →

Partners in
01Greece
02Europe
03Americas
04Asia
05Africa

Bring it in for a run on the dyno today!